2005 dodge ram radio removal?!


Question: 2005 dodge ram radio removal!?
i have a ram that i want to hook my satellite radio up to, but cant figure out how to remove the trim around the radio!. can you help!?Www@Enter-QA@Com


Answers:
Try this site, they have pictures of the removal!.


STEP 1!. Begin by removing the trim bezel around the radio
and climate control module!. Remove the 7mm hex head
screw located below the right-of-radio air vent!. (See
photos # 1 & 2)!. Open the glove compartment, grasp the
lower right corner of the bezel and pull out gently,
releasing a retainer clip!. Continue pulling outward as you
work your hands around the bezel, releasing all eight (8)
clips!. (See photo # 2)!. Disconnect the wiring harnesses to
the bezel and set bezel aside!.
STEP 2!. Remove four (4) 7mm hex head screws from the
four (4) corners of the radio!. Slide the radio out of its
cavity and let it hang down!. It is not necessary to
disconnect the wiring to the radio!.
STEP 3!. Place the Legend VSM against the dash pad in the
upper right corner of the radio cavity!. The Legend needs
to be slid to the far right edge of the cavity!. Using the
Legend as a guide, mark the location of the three (3)
mounting holes!. Set the Legend aside!. Using a 5/64” drill
bit and drill, drill three (3) pilot holes, approximately 3/8”
deep at the marked locations!. Position the Legend over
the pilot holes, insert three (3) # 8 x 1/2” screws and
tighten!. Reassemble the dash in reverse order!.
This completes the installation of your Pro!.Fit Legend!.
5/64” drill bit and drill, # 2 Phillips screwdriver, 7mm nut driver
Pro!.Fit Legend, instructions, three (3) #8x1/2” screws, hardware pack
Upper right corner of dash
110305-00
PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS Pro!.Fit Legend!.
All instructions assume a drivers seat vantage point!. Caution is advised when removing and reassembling
wood or plastic parts of a dash!. Applying unnecessary force or pressure may cause a piece to crack or break!.
TOOLS REQUIRED:
PARTS INCLUDED:
LOCATION:
Pro!.Fit International, Inc!.? may not be held liable for any damage to a vehicle before, during or after the installation or removal
of this Pro!.Fit Legend!. Pro!.Fit may not be held liable for any personal injury resulting from accident or improper installation!.
Pro!.Fit International, Inc!.? 1335 Eagandale Court, Eagan, MN 55121, Ph: 651-688-3588 or 800-388-0073 Fx: 651-688-9876
? Pro!.Fit International, Eagan, MN 2005
VIEW INSTRUCTIONS & UPDATES
ONLINE @
WWW!.PRO-FIT-INTL!.COM
PART NUMBER: DG-70-05-L
Dodge Ram (2002-2005)
Dodge 2500, 3500 (2003-2005)
4
3
1 2
Clip Holes
in Circles
7mm Hex
head screw



The site is in pdf so you will need Adobe Reader for the pictures!.

Go to: www!.pro-fit-intl!.com
click on it, then scroll down to the 29th listing, which will be: Part Number: DG-70-05-L Dodge Ram (2002-2005) Dodge 2500,3500 (2003-2005)
click on it and you will get the pics in pdf format!.Www@Enter-QA@Com



The answer content post by the user, if contains the copyright content please contact us, we will immediately remove it.
Copyright © 2007 enter-qa.com -   Contact us

Entertainment Categories